How to Do Clean Pull
Start and end of one clean rep of Clean Pull.
Quick facts
| Primary muscle | Quads |
|---|---|
| Secondary muscles | Forearms, Glutes, Hamstrings, Core, Back |
| Equipment | Barbell |
| Category | Olympic weightlifting |
How to perform Clean Pull
- With a barbell on the floor close to the shins, take an overhand or hook grip just outside the legs. Lower your hips with the weight focused on the heels, back straight, head facing forward, chest up, with your shoulders just in front of the bar. This will be your starting position.
- Begin the first pull by driving through the heels, extending your knees. Your back angle should stay the same, and your arms should remain straight and elbows out. Move the weight with control as you continue to above the knees.
- Next comes the second pull, the main source of acceleration for the clean. As the bar approaches the mid-thigh position, begin extending through the hips. In a jumping motion, accelerate by extending the hips, knees, and ankles, using speed to move the bar upward. There should be no need to actively pull through the arms to accelerate the weight; at the end of the second pull, the body should be fully extended, leaning slightly back, with the arms still extended. Full extension should be violent and abrupt, and ensure that you do not prolong the extension for longer than necessary.
Muscles worked
- Quads (primary): extends the knee to drive squats, lunges and jumps.
- Forearms (secondary): controls your grip and keeps the wrist steady under load.
- Glutes (secondary): extends and stabilises the hip — the engine behind hinges, squats and sprints.
- Hamstrings (secondary): bends the knee and extends the hip through hinges and pulls.
- Core (secondary): braces the trunk and resists twisting to protect the spine.
- Back (secondary): pulls the arms down and toward the torso and keeps the spine stable.
Sets & reps by goal
| Goal | Sets × reps | Load | Rest |
|---|---|---|---|
| Strength | 3–5 × 3–5 | Heavy (~85%+) | 2–3 min |
| Hypertrophy | 3–4 × 8–12 | Moderate (~65–75%) | 60–90 s |
| Endurance | 2–3 × 15–20 | Lighter (~50–60%) | 30–45 s |
Pick the row that matches your goal. If you're newer, anchor in the hypertrophy range while you groove the form.
Form tips
- Keep the knees tracking in line with the toes and push the whole foot into the floor.
- Keep the bar path close and stacked over your mid-foot; letting it drift forward wastes force and loads the lower back.
- Prioritise speed and position over load — a fast, well-timed pull beats a heavier sloppy one.
- Control the lowering phase — a 2–3 second descent builds more than dropping the weight.
Common mistakes
- Letting the knees cave inward as you push out of the bottom.
- Loading the bar heavier than your form allows and turning strict reps into a whole-body heave.
- Muscling the bar up slowly instead of moving fast underneath it.
Frequently asked questions
What muscles does Clean Pull work?
Clean Pull mainly works the quads, with the forearms, glutes, hamstrings, core, back helping as secondary movers.
What equipment do I need for Clean Pull?
Clean Pull needs a barbell and plates (plus a rack or bench where the movement calls for one).
How many sets and reps should I do for Clean Pull?
It depends on your goal: about 3–5 sets of 3–5 heavy reps for strength, 3–4 sets of 8–12 for muscle growth, or 2–3 sets of 15–20 for endurance. Pick the row that matches your goal. If you're newer, anchor in the hypertrophy range while you groove the form.
Train Clean Pull with a coach in your pocket
Gimmy is your AI gym buddy — it programs Clean Pull into recovery-aware workouts, tracks your sets, and shows one score that tells you if it's working.
Get early access