How to Do Hack Squat
Start and end of one clean rep of Hack Squat.
Quick facts
| Primary muscle | Quads |
|---|---|
| Secondary muscles | Calves, Glutes, Hamstrings |
| Equipment | Machine |
| Category | Strength |
How to perform Hack Squat
- Place the back of your torso against the back pad of the machine and hook your shoulders under the shoulder pads provided.
- Position your legs in the platform using a shoulder width medium stance with the toes slightly pointed out. Tip: Keep your head up at all times and also maintain the back on the pad at all times.
- Place your arms on the side handles of the machine and disengage the safety bars (which on most designs is done by moving the side handles from a facing front position to a diagonal position).
- Now straighten your legs without locking the knees. This will be your starting position. (Note: For the purposes of this discussion we will use the medium stance described above which targets overall development; however you can choose any of the three stances described in the foot positioning section).
- Begin to slowly lower the unit by bending the knees as you maintain a straight posture with the head up (back on the pad at all times). Continue down until the angle between the upper leg and the calves becomes slightly less than 90-degrees (which is the point in which the upper legs are below parallel to the floor). Inhale as you perform this portion of the movement. Tip: If you performed the exercise correctly, the front of the knees should make an imaginary straight line with the toes that is perpendicular to the front. If your knees are past that imaginary line (if they are past your toes) then you are placing undue stress on the knee and the exercise has been performed incorrectly.
- Begin to raise the unit as you exhale by pushing the floor with mainly with the heel of your foot as you straighten the legs again and go back to the starting position.
- Repeat for the recommended amount of repetitions.
Muscles worked
- Quads (primary): extends the knee to drive squats, lunges and jumps.
- Calves (secondary): points the foot to power push-off and steady the ankle.
- Glutes (secondary): extends and stabilises the hip — the engine behind hinges, squats and sprints.
- Hamstrings (secondary): bends the knee and extends the hip through hinges and pulls.
Sets & reps by goal
| Goal | Sets × reps | Load | Rest |
|---|---|---|---|
| Strength | 3–5 × 3–5 | Heavy (~85%+) | 2–3 min |
| Hypertrophy | 3–4 × 8–12 | Moderate (~65–75%) | 60–90 s |
| Endurance | 2–3 × 15–20 | Lighter (~50–60%) | 30–45 s |
Pick the row that matches your goal. If you're newer, anchor in the hypertrophy range while you groove the form.
Form tips
- Keep the knees tracking in line with the toes and push the whole foot into the floor.
- Set the seat and pads so the machine's pivot lines up with the joint you're training before your first rep.
- Treat every rep the same — a repeatable setup and bar path is what lets you add weight safely over time.
- Warm up the pattern with a couple of lighter, submaximal sets before your working sets.
Common mistakes
- Letting the knees cave inward as you push out of the bottom.
- Leaving the seat or range on a setting that forces the joint into an awkward angle.
- Chasing weight jumps before the current load feels solid on every rep.
Frequently asked questions
What muscles does Hack Squat work?
Hack Squat mainly works the quads, with the calves, glutes, hamstrings helping as secondary movers.
What equipment do I need for Hack Squat?
Hack Squat needs the corresponding weight-stack or plate-loaded machine.
How many sets and reps should I do for Hack Squat?
It depends on your goal: about 3–5 sets of 3–5 heavy reps for strength, 3–4 sets of 8–12 for muscle growth, or 2–3 sets of 15–20 for endurance. Pick the row that matches your goal. If you're newer, anchor in the hypertrophy range while you groove the form.
Train Hack Squat with a coach in your pocket
Gimmy is your AI gym buddy — it programs Hack Squat into recovery-aware workouts, tracks your sets, and shows one score that tells you if it's working.
Get early access